Dear Welder Series… Hi Paul. Re your Mustang II Crossmember kit. Could I just buy the coilover and upper A arm adjustment box and cut my old shock/spring tower off? Could I retain my lower stock A arm set up and just shorten my existing upper A arms? I’m trying to salvage some of what …
Why Do We Do It? A Winter Car Show Comparison
Let’s make a few comparisons here… You abandon a perfectly fine bed too early in the morning, drink one too many cups of instant coffee on your way out the door, scrape your windshield and sit in a cold car, staring blankly at the windshield as the circle of vision slowly grows enough to navigate …
Winner of the February Photo Draw
Congrats, Jonathan! Jonathan sent in some pictures of his Welder Series sway bar install during February, and was chosen by the random computational software at www.random.org as the winner. There is $50 on your account here to be used against future purchases. If you haven’t sent in pictures of our parts on your car, please …
Dear Welder Series… 1966 C10 Mustang II?
Dear Welder Series… I just purchased a 1966 Chevy C10 and want to upgrade the front end. I was wondering if your 60” Mustang II cross member would work? I searched your archives but could not find where anyone had inquired about this in the past. I can’t believe I could be the first with …
Dear Welder Series… Mustang II: installed frame height?
Dear Welder Series… Hi I’m building a custom frame I want to run a Mustang ll I like how you sell them and I plan on buying one from you my question is if running air springs and a 24 inch diameter wheel how high should the frame rails be from the ground and with …
Dear Welder Series… MII & rear four link dimension questions…
Dear Welder Series… Hi there I’m working on figuring out ride height and road clearance for my 51 Chevy if I use your MII set up and have a few questions, hoping you can assist. 1. For your MII front crossmember, what is the distance from the underside of the chevy frame to the bottom …
Dear Welder Series… Mustang II crossmember dimensions?
Dear Welder Series… Interested in your mustang II crossmember with coil overs. How much does the crossmember weigh and how wide is it outside to outside at the lower control arm mount? Thanks. Steve. Dear Steve… The 56″ crossmember kit (shown below) with the upper arm brackets and coil-over mounts weighs 32 lbs. The two crossmember …
Dear Welder Series… Four Link for 1965 Mustang?
Dear Welder Series… Hi, I’m after a rear 4 link for my 65 mustang for general road use, no racing, do you have a setup similar to [the other guys] setups & if so prices & cost of shipping to California 90200, USA, unless you good rates to New Zealand, if you can help I’ll …
Dear Welder Series… brakes for LTD spindle?
I want to make sure your MII brake kit will fit my spindle (Ford LTD, looks the same as Mustang II), can you supply dimensions for the spindle mounting points?
Dear Welder Series… Corvette IFS Kits?
There may be others like me who prefer the Corvette suspension components to the Mustang II parts. Do you plan on doing something for us?
Dear Welder Series… Mustang II in a ’65 F100?
The problem is that I have a Twin I-Beam set up with no control arms....if I were to get your MII crossmember, how would I know what control arms, spindles, brake set-up, what size coilovers to get?
Dear Welder Series… Brake/Clutch for ’51 Shoebox?
Just was curious if you had any pics of the part #248300 booster bracket with brake and clutch pedal kit.
Dear Welder Series… Mustang II for 1937 Dodge Business Coupe?
Hello, I am looking for a complete IFS front end kit for my 1937 Dodge D5 Business Coupe.
Dear Welder Series… Mustang II for a ’64 Volvo?
I'm looking to do a 56" wide MII on a '64 Volvo PV 544.
Dear Welder Series… Mustang II for Sunbeam Alpine?
I have a 60 Sunbeam Alpine. It has a front track width of 51”. Can you supply a mustang II kit to fit?