Dear Welder Series… Hi Paul, I recently bought a coil over MII kit from you. I see a recommended ride height for the coil overs, but how about extended and collapsed length, or shock travel length? Thanks Matt Dear Matt… Matt, we define a coil-over’s ride height as eye center to center compressed 1/3 of …
Dear Welder Series… Four Link Dimension Question
Dear Welder Series… I have a few questions on the parallel rear 4 link kits. Wondering what the measurement is between the two bars, C-C. Also what size tubing is used? I would like 1″ or 1 1/4″ if possible. I have purchased and installed the notch kit with great results, thank you for offering …
Dear Welder Series… Dodge Frame Question
Dear Welder Series… Mr.Horton, looking at the pictures of the cross member installation in the 36 Dodge Humpback, I do not see (any) modifications to the hump in the frame. Is your cross member ready to install without modifications? I have seen many pictures where the hump is taken out of the frame on other …
Mustang II Installed Pics: 1952 Chevy Pickup
As Steve was installing his Welder Series coil over Mustang II crossmember, he snapped some pictures (do you still snap pictures with a digital camera?) and sent them to be added to our monthly photo sharing draw. I know he’s bought a triangulated four link for the same truck… I can’t wait to see those …
Dear Welder Series… 52″ track width Mustang II?
Dear Welder Series… I am interested in replacing the MGB front suspension in my Cobra replica. I am planning to buy your unwelded coilover cross member and cut it down to make the pivot points of the lower a-arm match the pivot points of a MGB steering rack and fabricate rack mounting brackets for it. …
Dear Welder Series… trailer hitch for 1934 Pontiac?
Dear Welder Series… Do you have any trailer hitch parts to build a trailer hitch for a 1934 Pontiac? Thanks Burl Dear Burl… There aren’t any specific trailer hitch parts in the Welder Series catalog, Burl, but I’m sure a few of the tabs and gussets could be used. Thanks for looking at our site.
Dear Welder Series… will original Mustang II parts fit?
Dear Welder Series… Is your crossmember compatible to the original Mustang II upper and lower A arms? I am building a 36 Dodge Sedan D2. Thank you..Tommy Dear Tommy… Yes, Tommy, our crossmember is compatible with stock upper and lower arms from 1974 – 78 Mustang II and 1974 – 80 Pinto. You may want …
Dear Welder Series… Mustang II for 1947 Chevy 3800?
Dear Welder Series… I am looking for a mustang 2 front crossmember that I can weld my self. I see you have one for a model A but I need one for a 47 Chevy 3800. Is it the same one or do you offer a different one for different vehicles? Thanks, Derek Dear Derek… …
Dear Welder Series… Mustang II Installation Instructions?
Dear Welder Series… I purchased a Welder Series coil over front end kit for my 1952 GMC pickup. During the process I seem to have misplace my installation guide instructions. Can you mail me a new copy or email me a new copy either would be of great help. Dear David… David, check out the …
Dear Welder Series… 4.6l in a ’65 Mustang?
Dear Welder Series… Hi, I was wondering how long it typically took to receive the “Ford Motor Mounts, 4.6L/5.4L/Coyote, Urethane Insulated” kit that you have to offer on your site? My project car is up in Pennsylvania so I am not certain what I need at this time, but it looks like your kit might …
Bracket Compar-O: Why Welder Series?
We’ve spent a good deal of energy focusing on quality parts… quality steel, quality laser cuts, quality machining, and especially quality welding. When we see parts installed at a show, we can pretty much always tell if they’re Welder Series parts based on the weld and edge quality. That said, when a customer came in …
Dear Welder Series… Engine Angle Question
Dear Welder Series… I am building a 37 two door sedan. I have put in one of your Mustang II front suspension kits, which worked fine. Now I am installing the motor, which is a 1999 LS1 5.7L. My question is how important is the three degree tilt back on the engine. Three degree will …
Dear Welder Series… 1948 Chevy Pickup Mustang II?
Dear Welder Series… Good morning, I am restoring a 1948 Chevy pickup. I was inspired by the guys in Trucks. I want to upgrade the suspension but I am not sure what kit I need to order. Can you help me? I would like to get a complete front suspension kit. Thank you, Jesse Dear …
Dear Welder Series… Mustang II for 48-52 F1 Pickup?
Dear Welder Series… I’m interested in the you weld it crossmember you offer for 1948 to 52 ford F1 pickups. If I have a Ford pinto donor car will everything swap out to your crossmember? Or are there additional parts I need to buy like aftermarket control arms? Thanks for your help. Dear F1 Pickup …
March 2012 Photo Sharing Winner
Duane sent in a few pics of the ’32 3 window he’s building. Good grief, this thing sits perfect. Duane used our front four link kit, Panhard bars (front & rear), front shock mounts, Vega steering box mount, U bolt kit, tie rod & drag link, frame rail boxing plates, some motor mount pieces, and …