Dear Welder Series… I am interested in your Mustang II conversion for a 68 Mustang which will have a late Mustang 5.0 motor and t5 transmission. What I would like to know is, can I use Granada spindles and the stock Mustang control arms with this crossmember. Also, if I can’t use them what ones will work with …
Dear Welder Series… Motor Mounts for ’56 Chevy Pickup?
Dear Welder Series… Hello, I am emailing to find out if you have a Chevy V8 mount kit that will work in a 1956 Chevy pickup truck. Thanks, Jase Dear Jase… Jase, either of our Chev motor mount kits will work in your ’56. The frame brackets must be trimmed to put the engine at …
Dear Welder Series… Model A Mustang II Question
Dear Welder Series… Will the MII hub to hub IFS for a 1928-31 fit on a 2×3 rectangular frame? Also what is the min and max width it will fit. I’m building a 1927 full fendered Ford. Thanks Dear Howard… Howard, our Model ‘A’ Mustang II crossmember (below), is designed to fit a stock or …
Dear Welder Series… Jeep Parts?
Dear Welder Series… I am building an old school Jeep CJ5. I can’t find any aftermarket frames or frame parts anywhere. What are the chances you are going to start making some? How about a 1955 CJ5 frame kit? The CJ5 frame is the same from 1955 to 1971. Thank you for your time. I …
Dear Welder Series… 1969 F100 Four Link?
I need to know if your universal triangulated or 4 link parallel would work on my 1969 F-100.
Dear Welder Series… Deuce Only?
Dear Welder Series… Mr Horton: I have two major regrets. One is selling my 5 window deuce when I came home from Nam. The second is that I didn’t find your web site sooner. I would like to use your “Welder Series” Mustang II cross-member and coil mounts but I’m wondering which manufacturer’s tube arms …
Dear Welder Series… 1957 GMC truck four link?
Dear Welder Series… Hi, I contacted you last year before Christmas sometime and was going to order up a rear 4 link with air bag brackets. Since then things have changed and now I will be doing the same thing but with a smaller axle. It is the gm 8.5″ from an S10. The axle tube …
Dear Welder Series… 1968 Chevy pickup rear suspension?
Dear Welder Series… I have a 68 Chevy c10 pickup that I would like to replace the trailing arms w an adjustable 4 link setup using a Chevy 10 bolt rear. I would like to delete the Panhard bar also. What do you recommend? Do you have a complete kit with shocks and springs? Thanks …
Dear Welder Series… 1952 Ford Mainline Mustang II?
Dear Welder Series… I have a 1952 Ford Mainline I am looking for a kit for the front end of this bad boy. I want to airbag the front at the end of the day. Do you have a kit for this. Thanks for your time Mike Dear Mike… Mike, putting a Mustang II in …
Dear Welder Series… 1948 Ford Mustang II frame question.
Dear Welder Series… I have purchased your Mustang II Crossmember kit for my 1948 Ford Tudor sedan. I’m using the factory X-frame, at the front section where I am to install the crossmember there are the original frame holes. My question is do I have to box in the frame rails or can I plug …
Dear Welder Series… early Ford caliper brackets?
Dear Welder Series… Hey DW Do you have caliper brackets for early Ford spindles? Thanks Ross Dear Ross… Sorry, Ross, we don’t make early Ford brake brackets. Thanks for looking at Welder Series parts.
New Product: Universal Center Section Kit
This center section was designed with not only the center section in mind. Design points considered: – Change transmissions without relocating the tubes on the frame. – Drop the transmission easily. – Run exhaust above the lowest tube. – Brake pedal/booster/master cylinder integration. – Resist frame twisting. It can be installed in frames up to …
SW Ontario Shop Crawl: Saturday, March 31
If you’re local or want to come and visit some high end shops in the Southwestern Ontario area, come out Saturday March 31. We’re kicking off at Schwartz Welding in Bloomingdale at 9:30, then going to a number of other local builders. Click on the link for a map. It’ll be a full morning!
Dear Welder Series… Ford 8.8 Four Link?
Dear Welder Series… I have a 1980 MGB and am installing a narrowed Ford 8.8 rear-end. I have a leaf spring original rear suspension and want to install a 4-link to my 8.8, with coil over shocks. Can you help me? Dave Dear Dave… Dave, our parallel rear 4-link kit could be used with a …
New Product: Ford 8.8 Rear Four Link
We’ve just designed a bracket to be used with the upper bushing on a stock Ford 8.8 rear end. The triangulated design eliminates the Panhard bar, and the 8.8 rear end has been a common hot rod rear axle for a long time. This kit uses the 1-3/4″ wide bushings and 3/4-16 adjusters. Available ready …