Dear Welder Series… Hi Paul, i have a 56 chevy wagon and know for a fact that because the location of the fuel tank the only way i can place a 4 link in the car is putting the bags in front of the axle. Can i modify this kit to do it and work …
Dear Welder Series… 4 link custom bars?
Is it possible to get longer lower bars so I locate the bracket in the same spot as the reinforced part of the frame where the leaf spring hangers were mounted?
Syracuse Nationals
We’ll be heading to the Syracuse Nationals next weekend (July 17/18/19) which is always a good time. For a couple of years we didn’t have vendor space, but this year we decided to get 20′ outside, right in the thick of things in the same aisle as Tucci Hot Rods. The Welder Series ’32 will …
New Website Design
Over the past few months, I’ve been transitioning (no not like that) web store products over to a new web store system (click here to check it out). This is kind of like getting a new interior – you have the same car, same steering column, same brake pedal, only it’s all covered up in …
1963 Chevy Mustang II Installed Pics
Sean sent these pictures in of his Chevy II install. Nice work! He used our 56-1/2″ coil-over Mustang II crossmember kit.
Dear Welder Series… which master cylinder?
Dear Welder Series… Good morning! I was just wondering if you had a suggested master cylinder to use with your universal under floor brake kit? Is there one from a specific vehicle that I can pick up from the local parts store? I have also attached a couple pictures for you of some of your …
32 Driving Video #3
Maybe it’s #4. Or 7. I picked up a Wasp camera the other day to make it easier to shoot how-to videos, and it seemed like a good idea to strap it on the frame rail and go for a drive.
Dear Welder Series… No Door Mustang II?
Dear Welder Series… Hello from so-cal! do you want to make a lot of people happy? please make a mustang 2 crossmember kit for our 61-67 ford econoline vans and trucks! these things wander all over the road when lowered, and are a handful to drive. one problem is steering column ends up in front …
Dear Welder Series… X Frame Four Link?
Dear Welder Series… Hello, I know your product is universal but am wondering if you know of, or have experience with using this on an “X-Frame” car. I have a 1957 Cadillac which is an “X-frame” that I’m considering using your kit on. I thought I might as well ask to see if you have …
Dear Welder Series… four link for towing?
Dear Welder Series… Can these be used on a crew cab dually that will be doing some towing up to 10,000 lbs? Also is the hole cut big enough to fit over a 14 bolt which I believe is larger than most street axle tubes?? Dear Corey… Corey, we make parts for street rods/hot rods …
Dear Welder Series… Crown Vic motor mounts?
Dear Welder Series… I am putting a 351m in a 2003 crown vic front suspension, any sugestions on motor mounts? Dear Vern… Vern, our Ford mounts are for blocks that have 2 vertical mounting holes on 7″ centers. If your block is like this, either kit will work well. https://welderseries.com/Ford-Engine-Mounts-Urethane-Bushed-p51163312 https://welderseries.com/Ford-Engine-Mounts-Rubber-Insulated-p51163328 I hope this helps. …
Dear Welder Series… LS engine mounts: ours or theirs
Here is your kit and the USA kit- just trying to see the price difference of $40.00 ($130.00 canadian for the US kit), plus the difference in extra tax ($20.00). They look about the same? Do you make yours there or bring in from USA?
Dear Welder Series… minimum thread depth?
Dear Welder Series… On the 5/8 – 18 adjuster kit, assuming it has approximately 2.5″ of threads on it, what is the least amount of thread that can be screwed into the 4-link bar and still be considered safe? The application is a 1952 Chevy pickup utilizing an 8.8″ Ford Explorer rear axle. It will …
Dear Welder Series… Pinto spindles?
Dear Welder Series… I have a question but not sure if i post it here or another way on the site. I am wanting to put pinto spindles on my 70 dodge dart (because i want to put a rack and pinion) and im going to be converting to tubular a arms and a k …
Wes Killins 1940-2015
This note was sent by Jim Prowse this morning: “It is with tears of sadness and dismay , that we advise of the death of our great pal and car buddy , Wes Killins. Wes died peacefully , approx 5 am, on Jan 31 2015 , with family by his side . Funeral will be …