Dear Welder Series…
I’m building a 1930 Model A on boxed ’30 frame. I want to use your flat crossmember in order to use a 1936 wishbone with the spring forward of the axle.
I want to know if I can place your flat crossmember in front of the stock cross member in order that I may keep the original design, i.e. radiator and fenders etc…??
Has anyone done this before??
I want the car as low as possible and the use of the intact ’36 wishbone. I intend on using cross rack steering and need the clearance as well.
Thanks,
Mike
Dear Mike…
Thanks for looking at Welder Series’ parts.
Our flat front crossmember is designed for a 1-3/4″ wide spring, like the 1928-34 Ford. The ’36 Ford used a 2″ wide front spring, so it will not fit in our crossmember. The ’36 spring is longer than the Model ‘A’ spring, so it can’t be adapted to the ’36 stock wishbone, either.
The ’36 axle will be a little wide to let you get the front end low. (The tires will be out at the edge of the fenders.) You might want to mock up your parts to see how it looks before buying any parts. The standard way to get a Model ‘A’ low is to use a 46″ dropped axle with a reversed eye spring with a low arch.
I hope this helps.
Paul Horton
Dear Welder Series…
Thanks Paul…….I already have the 31″ 1 3/4 reverse eye spring with a 6″ arc, now I need the 46″ axle. I wanted to use the 1936 wishbone unsplit but I guess I will have to split it after all.
Thanks again,
Mike
Dear Mike…
Mike, you might be able to use the wishbone unsplit and just cut off the spring perch extensions. The spring would mount above the axle.
Paul
Dear Welder Series…
YES, that’s what I intend on doing I just have to find the widest perch possible on the “I” beam. The wishbone is 39.5″ apart and the “I” beam I have is 36″ and I have a feeling that the 46″ axle will also have around 36″ between bosses. Maybe I can bend the wishbone to match the bosses when I get the 46″ axle.
Worse scenario is splitting the wishbone…………..
Since I have you online, do you guys sell “X” crossmember for the model A frame? I need something for my 4L60 transmission to bolt onto. I’m running a 283 cu. in. motor as well and will also need the motor mounts to weld to the frame and attach to the motor, side mounts.
I have a 1930 model A frame that is completely stepped up and boxed. I have a center cross member but I would like to reinforce the frame a little more and have the setup to bolt on the brake pedal, etc..
Thanks again,
Mike
Dear Mike…
Mike, most 46″ axle perch centers are about 34-1/2″. You should be able to bring the wishbone in to match the 46″ axle perches. Make sure the ball stays in the center.
We don’t have a Model ‘A’ x-member. Check Dagel’s https://dagels.com/super-x-crossmember-kit/. Welder Series does have Chev motor mounts.
Classic Rods & More (Lynchburg, VA) and Welder Series can now provide you with a PROVEN MII IFS Kit for your 1928-31 Ford Model A that will give you a low stance and maintain your wheels in the center of the front fenders. This IFS has been produced and used for a number of years by one of the owners of Classic Rods & More and maintains the stock MII geometry. It does not require bubbling the front fenders in order to clear the A-Arms. The front splash apron will require modification. 2″ dropped spindles and 1″ narrowed A arms required. Front end alignment is achieved by using stock MII specifications.
The kit will not require any additional manufacturing to install. Once the kit is welded just place the crossmember on the front axle centerline, place the tower centerline on the same front axle centerline on the outside of the frame rails and weld in place.
Available welded or as a ready-to-weld kit.
Hub-to-hub kits are available from Classic Rods & More and other dealers who assemble complete Mustang II kits.
The sedan in the pictures is using this crossmember with 15×6 wheels.
Our Model ‘A’ manual brake pedal is at:
I hope we can help with your project.
Paul Horton