Dear Welder Series…
Looking at the brake booster kit WS24806. Can you get the same kit but with a pedal arm that is flat with no kinks or bends. If so, will it be the same price?
Thanks
Jay
Kelowna BC
Dear Jay…
We can sub any pedal in the kit Jay. Here are the parts and pieces of pedal kits.Sway Bar Kit, Trim To Fit, 1" BarProduct DetailsMay 29: splined bars are sold out; bars will now be supplied with smooth ends to be pinned.
Available 45″ wide, but can be cut down (with a hack saw) to any length. The bar is 1” diameter solid 4142 heat treated, cold finished. Both ends of the bar will be smooth. This smooth end gets securely drilled/pinned with a 1/4" coiled spring pin and/or welded (optional) into a coupler which welds to one of the arms. The laser-cut, 3/8″ thick arms are 8″, 12", or 17" center-to-center. Optional Delrin bushings isolate the sway bar inside a 1-5/8" OD DOM outer tube. Adjustable rod ends connect the arms to the tabs that weld to the rear end or frame. Overall length is ¾” longer than the bar length, since the 3/8″ arms mount outside the ends of the bar. The arms can be bent to clear the coil-overs or, if used as a front sway bar, to clear the tires when turned.
About the coiled spring pins we use: These spiral pins remain flexible after installation, so they absorb shock and vibration better than slotted spring pins. Tension holds them tight against the hole wall. The chamfered ends aid insertion. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces. The pins have a breaking strength of 5500 lbs.
How To Order:
The standard price includes a 1" dia, 45" long solid sway bar with the hardware package pictured below.Work your way down the options list, selecting how you want to mount the bar and arms.
If you'd rather order over the phone, please call us toll free at 1-888-648-2150. We can walk you through the various options.
Hardware Package
This is the basic hardware package that comes with every kit. Heim joints are Teflon lined and made in the USA. They now come in a yellow zinc plating. Both couplers are supplied with 1" smooth ID couplers.
Arm Mounting Options:
Axle Bracket Tabs
Designed to mount the heim joints to 3" axle tubes. 10 ga. 3/8" hole.Frame Mounting Tabs, 11/16"
These 3/16" thick tabs will mount the heim joints nice and close to your frame rail. 3/8" hole.Long Frame Mount Tabs
If you need some more distance between the arm and the frame rail, these 3/16" tabs tabs might be the solution. 4" from the frame edge to the 3/8" hole center.Control Arm Tabs
Typically used to mount the heim joints to a 1" dia tubular lower control arm. 3/16" thick, 3/8" hole.Sway Bar Mounting Options
Pillow Block Bearing Mount
If you want to mount your sway bar underneath the frame using pillow block bearings, here is the option for you. Select "no outer tube" and "no outer tube mounts". These bearing mounts have set screws at 12:00 and 3:00 to keep the bar from moving side to side. Just use a drill bit to create a small divot for a more secure connection. They will accept some misalignment as the bearing is mounted in a rounded cage and will pivot.
If your unboxed frame is already painted and you want a bolt-on kit, please see the related parts below for a bolt-on pillow block bracket.
Note: bars will not be supplied splined.
Two pillow block bearings are supplied. For mounting hardware options, see below.
Pillow Block Mounting Hardware
Option A: 3/8-16 nylok nuts for mounting to an unboxed frame rail where you have access to the nuts. Includes two pillow block bearings.
Option B: 3/8-16 threaded bungs to weld into a boxed frame rail. Includes two pillow block bearings and lock washers.
Option C: 3/8-16 tab weld nuts to weld inside the frame rail before boxing. Includes two pillow block bearings and lock washers.
Tube Mount
Like our 3/4" sway bar kit, this kit is also available with a 1-5/8" OD x .188" heavy wall outer tube mount. The 1" bar is isolated with CNC machined Delrin bushings. This outer tube can be installed through the frame rails to mount the arms outside the rails. It is strong enough to be used as a crossmember to mount coilovers or Shockwaves to.Under Frame Mount:
These plates have two 3/8" mounting holes, with the opposite end designed to weld to the 1-5/8" outer tube. With this option, the sway bar can be mounted underneath the frame rails. We have weld-in threaded bungs and hardware available to fasten the plate, if required. 1" from the top of the 1-5/8" tube to the mounting hole centerline.Sway Bar Kit, Trim to Fit, 3/4" BarC$177.00Sway Bar Kit, Trim to Fit, 3/4" Bar36" and 45" lengths, select options to build complete kit.We would credit the arm #213211 (standard in the kit) and invoice for the pedal you want.
Thanks for looking at the flexibility of Welder Series part numbers.
Paul Horton
