Online Store

Mustang II Caliper Bracket Kit, for Granada rotors

2125
C$107.00
In stock
1
Product Details
Brand: Welder Series
Thickness: 3/8"

Brake kit for 1974 -78 Mustang II and 1974 – 80 Pinto/Bobcat spindles. This kit adapts larger 11″ Granada rotors and 1982 – 92 Camaro (or equivalent) calipers for a simple, effective, and inexpensive brake upgrade. Some 14″ wheels will clear the calipers. 15″ wheels will clear. The 1975 – 80 Granada rotors move each wheel out 1/4″ from stock Mustang II rotors.

Welded kit includes all hardware included in the ready-to-weld kit.

INSTALLATION INSTRUCTIONS

WELDER SERIES’ PARTS ARE TO BE ASSEMBLED AND INSTALLED BY QUALIFIED WELDERS. THE PURCHASER OF WELDER SERIES’ PARTS MUST ESTABLISH THE SUITABILITY OF THE PARTS AND THE QUALIFICATIONS OF THE PERSON WELDING THE PARTS. WELDER SERIES PARTS, WELDED IMPROPERLY, COULD FAIL AND CAUSE INJURY OR DEATH.

This kit includes caliper mounting brackets (driver & passenger sides are different – they will not fit on the wrong side), and mounting hardware. Use the hardware in the kit to mount the caliper brackets. DO NOT USE THE STOCK FORD HARDWARE – IT IS NOT THE SAME THREAD!! The photo shows the kit mounted on the passenger spindle.

The stock Mustang II dust shield must be removed from the spindle and discarded. The Granada rotors fit onto the Mustang II spindles using stock Granada bearings, seals, outer washers, nuts and dust covers. Stock Mustang II spindle nuts can be used.

The end of the lower control arm must be ground away for rotor clearance. DO NOT INSTALL THE ROTOR UNTIL THIS CLEARANCE HAS BEEN ESTABLISHED. 1/8 inch clearance is enough.

Use stock brake pads (#7070A or FMS #D154) for the calipers.

NOTE: The squealer tab on the inside brake pad must be bent 1/8” toward the rotor surface. This can be done by carefully tapping it with a hammer. The outer pad tabs may need to be bent slightly to tighten the pad on the caliper. This will keep the pads from squeaking.

Stock GM calipers have a lip around the brake hose port. Grind this lip and rotate the hose fitting so it clears the coil spring when the steering is at full turn lock. Be sure the brake flex hoses do not touch wheels, tires or any other parts under any suspension travel or cornering conditions.

Parts Included:
Plate, caliper mounting plate for Granada rotor and GM caliper on Mustang II spindles. 3/8″ thick, 21255, 2
Spacer, steel, 1″ OD x 1/2-20 threaded ID x 3/4″ long, 21252-A, 2
Spacer, steel, 3/4″ OD x 7/16″ ID x 5/8″ long, 21253-A, 2
Bolt, 7/16-14 RH x 1-3/4″, Grade 5 hex, zinc plated, 2
Bolt, 1/2-20 RH x 2″, Grade 5 hex, zinc plated, 2
Washer, 7/16″ lock, zinc plated, 2
Washer, 1/2″ lock, zinc plated, 2
Washer, 1/2″ SAE, zinc plated, 2

Assembly Tips:
Use a pair of 1974-78 Mustang II spindles as a fixture. This way the parts will be held in exactly the right place for tack welding.

The end of the threaded spacer (for the ½-20 bolt) should bottom against the slot in the plate. Take the tacked assembly off of the spindles to finish welding. Avoid getting weld inside the threaded spacer.

Be sure to read the installation tip sheets shipped with each kit.

Save this product for later